





AQUA-SEAL GOLD+ Professional Grade, Premium Stone, Tile & Grout Sealer
Product details
- Does Not Contain PFOA/PFOS/PFHxS (NanoPlus)
- RapidPlus + ActiveShield
- Premium stain resistance against water, oil, grease, food
- Low VOC (<5 g/L)
Couldn't load pickup availability
Pickup available at KURNELL
Usually ready in 24 hoursProfessional Grade · Sealers Plus (an Aqua-Seal brand)
Fast dispatch from Kurnell, NSW
Not sure? Call +61 2 9521-4000

AQUA-SEAL GOLD+ - Professional Grade, Premium Stone, Tile & Grout Sealer
Full description
About AQUA-SEAL GOLD+
Premium natural look sealer for stone, terrazzo, grout, encaustic tiles, cement etc. NanoPlus formula.
Technical Bulletin (PDF) ›Description
Aqua-Seal Gold+® is a Professional Grade, low VOC (<5 g/L), natural look, no sheen, breathable, penetrating sealer. Using advanced short-chain C6 technology, it delivers our highest level of stain resistance – the premium tier of the Aqua-Seal sealer range – helping resist water, oil, grease, food and grime. Water based, non-flammable, non-yellowing, UV and chemical resistant. Built-in RapidPlus gives stain protection in 4 hours. Also use as a pre-grouting sealer. Does not contain PFOS, PFOA or PFHxS.
How does it work
NanoPlus C6 sealing molecules penetrate deep into the surface, then chemically bond and reduce the size of the open pores, reducing porosity. Liquids can then be wiped from the surface before they stain. Spills should be wiped up immediately to help minimise staining.
Works on & where to use
All porous surfaces: natural stone (e.g. Basalt, Bluestone, Granite, Marble, Limestone, Quartz, Slate, Sandstone, Travertine etc), terrazzo, encaustic and porous porcelain tiles, grout, bricks, Saltillo, terracotta, concrete and pavers. Suitable for food preparation surfaces once fully cured, e.g. bench-tops, table-tops and bar-tops. Not for glazed or non-porous tiles, or surfaces with an existing sealer or coating.
Use in domestic and commercial, indoor and outdoor areas: homes, hotels, airports, retail, kitchens and restaurants.
Coverage
APPROXIMATE COVERAGE – m² per Coat – Apply minimum 2 coats
| Surface | m² per 1 L per coat | Coats |
|---|---|---|
| Bluestone Flamed | 15–20 | 2+ |
| Encaustic Tiles | 8–10 | 2+ |
| Granite Flamed | 15–20 | 2+ |
| Marble Honed | 15–20 | 2+ |
| Limestone Polished | 20–25 | 2+ |
| Sandstone Honed | 10–15 | 2+ |
| Terracotta (Pressed) | 15–20 | 2+ |
| Terrazzo Polished | 20–25 | 2+ |
| Travertine Honed | 15–20 | 2+ |
Approx 10–40 m² per 1 litre per 1 coat (minimum 2 coats recommended). Will vary depending on the density, porosity, texture and absorption of the surface. Also weather conditions, application method and number of coats required. Use the free Sealer Calculator at sealersplus.com.au.
250 ml: Approx 2.5–10 m² per 250 ml per 1 coat (minimum 2 coats recommended).
PREPARATION & ALWAYS TEST FIRST
- Protective gloves, eye, skin and foot protection
- XtremeClean+ or Stone Wash+ to clean and prepare the surface
- Sealer applicator, pump sprayer, sealer sponge, brush, roller or paint pad, plus a plastic container or paint tray
- Plenty of paper towels or clean absorbent cotton cloths
Preparation: clean the surface with XtremeClean+ or Stone Wash+ as per the label. The surface must be clean, dry and free from other sealers and coatings.
Test first: always test first in an inconspicuous area to check coats needed and colour stability. End user must determine suitability of product for their own use.
How to apply
- Apply sealer to a clean, dry surface using a sealer applicator, pump sprayer, sponge, brush, roller or paint pad
- Ensure an even coat, then work the sealer in thoroughly
- Do not let it dry on the surface. Add more sealer to keep it wet for the 10-15 minute period
- After 10-15 minutes, wipe the surface completely dry with absorbent paper or cotton towels
- Repeat for each coat. Minimum 2 coats; porous surfaces may need more. Vertical surfaces: work bottom to top and avoid run-down.
Application notes:
- Porous surfaces need extra coats. Allow at least 30 minutes between coats
- Water drop test: 2 hours after the final coat, test with a few water droplets. If water soaks in, apply another coat, wait 2 hours and test again
- Light traffic after 2 hours. Keep dry for at least 24 hours. Full cure in 24 hours
HOW TO USE – PRE-GROUT SEALING
- To help with the grouting process of porous surfaces and minimise staining from grout and adhesive;
- Pre-seal before installing, or 24 hours after installation. Do NOT saturate open grout joints;
- Allow minimum 24 hours cure before grouting;
- Dark or contrasting grout, or rough porous surfaces: apply Grout Release+ after Aqua-Seal Gold+® has cured, before grouting;
- Tip: add Haze Away to the final rinse water when grouting to help prevent grout haze.
Limitations, expected wear & other options
Limitations: Aqua-Seal Gold+® is a penetrating sealer, not a waterproofing membrane: it will not prevent surface wear, scuff marks or etching from harsh or acidic products. Wipe up spills immediately.
Expected wear: varies with surface texture and hardness, traffic, and how often and with what it is cleaned. Pressure washing, high alkaline, acidic or solvent cleaners and weather exposure affect wear. High traffic and exterior areas need re-sealing more often. Re-seal as necessary.
Other sealer options: for a non-gloss colour enhanced look use Enhance'N'Seal. For a gloss finish use Gloss'N'Seal.
Maintenance
- EzyClean+ for rinse free, streak free everyday/weekly cleaning and disinfecting
- XtremeClean+ for heavy duty monthly/quarterly cleaning and disinfecting
- Stone Wash+ for monthly/quarterly cleaning, conditioning and disinfecting
- Stone Gel+ for cleaning vertical surfaces and disinfecting
- Boost Plus for everyday/weekly cleaning and re-sealing
- AquaGuard spray cleaning and re-sealing, everyday/weekly
- ReFresh+ for daily food-surface cleaning and disinfecting
250 ml – table tops / benchtops:
- EzyClean+ – routine everyday / weekly cleaning;
- XtremeClean+ – heavy duty cleaning & degreasing;
- ReFresh+ – spray & wipe cleaning & disinfecting;
- AquaGuard – spray & wipe cleaning & re-sealing;
- Stone Wash+ – deep cleaning & conditioning;
Precautions & safety directions
- Read the entire label, SDS and technical bulletin before use
- Wear gloves, skin, eye and foot protection
- Use when the surface temperature is between 4°C and 32°C
- Surface must be clean, dry and free from other sealers and coatings
- Do not allow sealer to drip or leave drip marks
- Do not use on the underside of tile or stone. For six-sided/dip sealing use Condense Plus or Ultra-Block first
- Keep away from non-recommended surfaces;
- WASH UNDERSIDE OF SHOES BEFORE STEPPING ONTO OTHER AREAS.
Handling, storage, clean up & first aid
Storage: close tightly after each use. Store in the original container between 4°C and 32°C. Shelf life approx 3 years unopened, less once opened. Do not re-use the container. Clean tools and clothing with water.
First aid: contact a doctor or Poisons Information Centre (Aust 13 11 26, NZ 0800 764 766). First aid is not generally required. Do not induce vomiting; wash mouth with water. Eyes: flush with clean running warm water for at least 5 minutes. Skin: rinse with clean running water.
How to use, product details and information
What to use on
Surfaces
Finishes
- Brushed
- Flamed
- Honed
- Polished
- Rough/Highly Textured
- Sand Blasted
- Textured
- Tumbled
Tap a surface to see every product for it. Always test in an inconspicuous area first. Not sure? Use the Product Selector below.
How much do I need?
WATCH: HOW TO USE
Aqua-Seal Gold+® in action
How penetrating sealers work
Questions about a product or your project? Our team is here Monday to Friday.
-
Call us
-
Email us
-
Shipping
See our shipping policy for delivery times and costs.
-
Product Selector
Answer 3 quick questions on our Product Selector.
