HOW TO REMOVE GROUT HAZE FROM NATURAL STONE

Step-by-step instructions for marble, limestone, travertine and other natural stone, plus encaustic and terrazzo tiles and other acid-sensitive surfaces, from the team who make Sealers Plus Professional Grade products in Kurnell, NSW.

Problem solver · Grout haze · No acids

Pre-wet, pour, scrub, rinse

MicroScrub is a powerful, Professional Grade Nano-Cream cleaner that is non-flammable and contains no VOCs or acids. Its fine nano-abrasive helps remove light grout haze (including light epoxy grout haze) from acid-sensitive surfaces without the etching risk of acid cleaners, and it is formulated not to affect penetrating (impregnating) sealers.

  • Ready to use Nano-Cream: no dilution. Pour, scrub and rinse
  • Non-acidic, no VOC: for acid-sensitive surfaces (test first)
  • Pour approx. 1–2 cups (250–500 mL) onto the pre-wet surface
  • No dwell time needed. Don't let it dry on the surface: add a little water
  • Pick up with a wet vac or mop, then rinse thoroughly
  • Take care on polished, glossy and dark coloured surfaces
MicroScrub
MICROSCRUB
250 mL · 1 L
$26.00 View product

What is grout haze?

Grout haze is the powdery cement residue left on tiles and stone after grouting when the clean-up during installation isn't thorough. The longer it stays, the harder it becomes to remove. It leaves the surface looking dull and dirty and can start to catch dirt.

WHY NON-ACIDIC? Acid grout haze removers can etch and dull calcium-based stone such as marble, limestone and travertine. MicroScrub contains no acids. Ceramic or porcelain tiles? Use Haze Away or OxiTreat+.

Watch the video

MicroScrub – How To Use – Sealers Plus

MicroScrub – How To Use – Sealers Plus

Suitable for

Where to use

  • Domestic: homes, units, duplexes etc
  • Commercial: hotels, shopping centres, restaurants, schools, aged care etc

Not for

  • Heavy or cured cement grout haze on acid-resistant tiles: use OxiTreat+
  • Deep-set stains or contaminants below the surface
  • Etch marks or dull, damaged polish: it won't restore polish

What you'll need

  • MicroScrub
  • Scrub'N'Clean Kit, white nylon pad, scrub brush or scrub machine
  • Broom and vacuum
  • Spray bottle or pump sprayer with clean water
  • Grout brush for the joints
  • Wet vac (recommended) or mop
  • Bucket, plenty of clean water and cotton towels
  • Skin and eye protection

Before you start

  • Always do a test area first
  • Surface temperature between 4°C and 32°C
  • Work out of direct sun so the product doesn't dry
  • Take extra care on polished, glossy and dark coloured stone and grout
  • Use a white nylon pad only on polished surfaces
  • Keep children and pets away until the area is rinsed and dry

Step-by-step

Prepare → Treat → Remove + rinse
Prepare the area1Prepare

Prepare the area

Sweep, vacuum or wipe the surface to remove loose dirt and debris.

Do a test area first2Prepare

Do a test area first

VERY IMPORTANT
Try MicroScrub on a small, hidden spot. Check colour stability, polish and dark grouts. Polished and dark surfaces may scratch or dull.

Lightly pre-wet3Prepare

Lightly pre-wet

Slightly pre-wet the surface and grout joints with clean water. On walls, spray water from a spray bottle.

Apply MicroScrub4Treat

Apply MicroScrub

Pour approx. 1–2 cups (250–500 mL) of MicroScrub onto the pre-wet surface. On walls, apply it directly to a white nylon pad. Work in small sections.

Scrub straight away5Treat

Scrub straight away

Scrub with a white nylon pad, scrub brush or scrub machine: no dwell time required. Don't allow the product to dry on the surface: add a little water to keep it wet and active.

Scrub the grout joints6Treat

Scrub the grout joints

Work the grout joints and edges with a grout brush.

Pick up and rinse7Remove + rinse

Pick up and rinse

Remove the dirty solution with a wet vac or mop, then rinse thoroughly with clean water and pick up the rinse water too.

Check when dry, repeat if needed8Remove + rinse

Check when dry, repeat if needed

Check the area once it is fully dry. Repeat as necessary until you're happy with the result.

How much? MicroScrub

Use How Amount
Floors Pour onto the pre-wet surface, scrub straight away 1–2 cups (250–500 mL) per section
Walls & vertical surfaces Spray water on the wall, apply to a white nylon pad, scrub Enough to keep the pad loaded
Booster Add to the standing solution of a cleaner or problem solver just before scrubbing As needed

Use as is: do not dilute. No dwell time required.

Tips for the best result

  • Treat light grout haze (including light epoxy grout haze) early: the older it is, the harder it can be to remove
  • Heavy build-up or residue older than 10 days may need several applications
  • Use a white nylon pad only. Never a black or green pad on polished surfaces
  • Work in small sections and keep the surface wet and active
  • Boost a cleaner: add MicroScrub to the standing solution of any Sealers Plus cleaner just before scrubbing
  • Next installation: add Haze Away to the final grout wash to help reduce haze

Aftercare

Aqua-Seal Gold+

For a natural look: re-seal porous surfaces with Aqua-Seal Gold+® once clean and completely dry, when water starts to absorb quicker than before.

Enhance'N'Seal

For a colour enhanced look: seal porous surfaces with Enhance'N'Seal instead. The colour change is permanent: always test first.

EzyClean+

EzyClean+: Daily / Weekly cleaning, pH neutral.

Stone Wash+

Stone Wash+: Quarterly deep clean for natural stone and terrazzo.

XtremeClean+

XtremeClean+: Half yearly or as needed heavy-duty clean.

Aqua-Seal Gold+® and Enhance'N'Seal are for porous surfaces only: natural stone, encaustic and terrazzo tiles and grout. Use the Product Selector to check the right sealer for your surface and finish.

Precautions

  • Read the entire label, SDS and technical bulletin before using
  • Wear appropriate skin and eye protection
  • Use when the surface temperature is between 4°C and 32°C
  • Do NOT allow product to contact any non-recommended surfaces
  • Take care on dark coloured grout or stone, and on polished or glossy surfaces
  • Keep floors dry to help prevent slips and falls
  • WASH UNDERSIDE OF SHOES BEFORE STEPPING ONTO OTHER AREAS.

Limitations

MicroScrub will not remove deep-set stains or contaminants below the surface, etch marks or damaged polish. It removes surface sealers and finishes only, not penetrating sealers. Heavy build-up may need multiple applications.

For other stains and problems, see our Problem Solvers and the Stain Removal Guide.

For additional options, contact the Sealers Plus Technical Services Team at support@sealersplus.com.au or call +61 2 9521-4000 with details of the problem you are addressing.

Important note

These recommendations are general guidelines for problem solving. Actual dilution ratios and cleaning requirements may vary depending on the surface, the use, the amount and the method of application.
Read the entire Product Label, SDS and Technical Bulletin before using any product.
ALWAYS TEST A SMALL AREA to determine the ease of application, dilution, dwell time and desired results.
Keep the surface clean and dry to reduce the possibility of slip-fall accidents.
Chat on WhatsApp