HOW TO REMOVE TANNIN STAINS FROM STONE, TILES, PAVERS & CONCRETE
Step-by-step instructions for natural stone, ceramic, porcelain, encaustic and terrazzo tiles, concrete, grout, pavers and bricks, from the team who make Sealers Plus Professional Grade products in Kurnell, NSW.
Mix, dwell, scrub, rinse
Active Plus is an easy to use, 100% actives, super concentrated, triple action oxygen cleaner, deodoriser and stain remover. Mixed with warm water, it helps remove algae, mould, mildew, leaf and tannin stains, dirt and grime. It is non-acidic, so it is suitable for acid-sensitive surfaces.
- Powder: General Cleaning 30 g, Heavy Duty 60 g or Extreme up to 120 g per 1 litre of warm water
- Use hot water for better results (never boiling)
- Allow 10–15 minutes dwell time. Don't let it dry on the surface
- Scrub, pick up with a wet vac, then rinse thoroughly
- Safe on natural stone, ceramic & porcelain tile, grout & concrete. Always test first
- Stubborn, deep-set stains: use the paste method
- Leaf-shaped marks? See remove leaf stains
What are tannin stains?
Tannins are natural plant compounds found in leaves, bark, timber, mulch, seed pods, tea, coffee and wine. When they get wet they leach out and soak into porous surfaces such as natural stone, concrete, pavers and grout, leaving brown, orange or yellow stains. Run-off from timber decks, planter boxes and garden beds is a common cause.
The longer a tannin stain sits, the deeper it can go, so treat it early. How well it lifts depends on the surface, how long the stain has been there and whether the surface was sealed.
Before & after

Suitable for
- All natural stone e.g. basalt, bluestone, granite, limestone, marble, quartzite, sandstone, slate, travertine
- Porcelain, ceramic, encaustic and terrazzo tiles
- Concrete, pavers, bricks, mosaics, terracotta and Saltillo
- Grout, indoors and outdoors
Where to use
- Domestic: homes, units, duplexes etc
- Commercial: hotels, shopping centres, restaurants, schools, aged care etc
Not for
- Plants, soil and metals (keep it away)
- Etch marks or dull, damaged polish: it won't remove etching or restore polish
What you'll need
- Active Plus
- Scrub'N'Clean Kit, white (light), blue (moderate) or black (heavy) scrubbing pad depending on severity, or a scrub machine; rough or heavily textured surfaces: a good quality stiff bristle brush
- Plastic bucket and warm/hot water (not boiling)
- Kitchen scales or a measuring cup
- Wet vac (recommended) to pick up the dirty solution
- Bucket plus plenty of clean water for rinsing
- Gloves, eye, skin and foot protection
- Paste method: plastic wrap, residue-free tape, plastic spatula, paper towels
Before you start
- Always do a test area first
- Surface temperature between 4°C and 32°C
- Sweep away leaves, mulch and debris
- Keep the solution away from plants, soil and metals
- Mix only what you'll use: never cover or store mixed solution
- Mix only what you'll use: never cover or store the mixed solution in a sealed container
- Keep children and pets away until the area is rinsed and dry
Step-by-step
Prepare → Treat → Remove + rinse
1Prepare
Sweep and pre-wet
Sweep away leaves and debris, then pre-wet the surface with clean water. On walls, pre-wet the wall and the ground below it, so run-off doesn't soak in and leave streaks.
2Prepare
Do a test area first
VERY IMPORTANT
Try the solution on a small, hidden spot to check surface colour stability and how well the stain lifts.
3Treat
Mix Active Plus
Stir Active Plus into clean, warm water in a plastic bucket: General Cleaning 30 g, Heavy Duty 60 g or Extreme up to 120 g per 1 litre, e.g. 120 g, 240 g or up to 480 g in 4 litres. For better results use hot water (never boiling). Stir until it dissolves.
4Treat
Apply generously
Apply the solution generously to the surface with a clean mop. Clean large areas in sections. On walls / vertical surfaces, apply from the bottom up and rinse from the top down.
5Treat
Allow 10–15 minutes dwell time
Allow to dwell for 10–15 minutes. Don't allow the product to dry on the surface: add more solution to keep it wet and active.
6Treat
Scrub
Scrub with a Scrub'N'Clean Kit and a white (light), blue (moderate) or black (heavy) scrubbing pad depending on severity. Rough or heavily textured surfaces: use a good quality stiff bristle brush to get in between the texture.
7Remove + rinse
Pick up and rinse
Remove the dirty solution with a wet vac, then rinse thoroughly with clean water.
8Remove + rinse
Check when dry, repeat if needed
Check the area once it is fully dry and repeat as necessary. Stubborn stain? Use the paste method below.
Mixing rates: Active Plus
| Use | Per 1 litre | Per 4 litres |
|---|---|---|
| General Cleaning | 30 g in warm/hot water | 120 g in 4 L |
| Heavy Duty | 60 g in warm/hot water | 240 g in 4 L |
| Extreme | up to 120 g in warm/hot water | up to 480 g in 4 L |
Dispose of any unused mixed solution after 4 hours.
Stubborn stains: paste method
- Mix Active Plus with warm water to a thick toothpaste / peanut butter consistency
- Apply a finger-thick, even coat over the stain, covering slightly more than the stain
- On walls: cover with plastic wrap and tape down all the edges with residue-free tape so the paste stays in place, then poke a few holes in the wrap. This step is required on walls; on floors, plastic wrap is optional
- Leave until the paste dries (24–48 hours depending on conditions), or for at least 24 hours
- Lift off with a plastic spatula, mist with clean water and scrub lightly with a white (light), blue (moderate) or black (heavy) scrubbing pad depending on severity, or a brush
- Rinse thoroughly with clean water, dry with paper towels and repeat as necessary
Tips for the best result
- Treat tannin stains early: the longer they sit, the deeper they go
- Fix the source first: cap or seal weeping timber, redirect run-off from planters and garden beds, and trim back overhanging plants
- Use hot (not boiling) water for better results
- Work in sections you can keep wet, and never let the solution dry on the surface
- For deep-set, stubborn stains, see the Stain Removal Guide
- Walls, vertical surfaces or a deep-set stain? Step by step with photos: Clean Walls & Floors with Active Plus and Remove Stains from Walls & Floors with Active Plus (paste method)
- Once clean and completely dry, seal porous surfaces with Aqua-Seal Gold+® for a natural look or Enhance'N'Seal for a colour enhanced look to help reduce future staining
Aftercare

For a natural look: re-seal porous surfaces with Aqua-Seal Gold+® once the stain is removed and the surface is completely dry.

For a colour enhanced look: seal porous surfaces with Enhance'N'Seal instead. The colour change is permanent: always test first.

EzyClean+: Daily / Weekly cleaning, pH neutral.

Stone Wash+: Quarterly deep clean for natural stone and terrazzo.

XtremeClean+: Half yearly or as needed heavy-duty clean.
Aqua-Seal Gold+® and Enhance'N'Seal are for porous surfaces only: natural stone, encaustic and terrazzo tiles, concrete, pavers and grout. Ceramic and porcelain tiles take a different sealer: use the Product Selector to find the right one for your surface and finish.
Precautions
- Read the entire label, SDS and technical bulletin before using
- Always test first
- Take care if using hot water to prevent scalding. Do not use boiling water
- Wear skin, eye and foot protection
- Use when the surface is between 4°C and 32°C
- Keep away from plants, soil and metals
- Once mixed, do NOT cover or store the mixed solution in a sealed container
- Dispose of any unused solution after 4 hours by flushing with plenty of clean water into a toilet or drain
- WASH UNDERSIDE OF SHOES BEFORE STEPPING ONTO OTHER AREAS.
Limitations
The degree of success depends on the surface stained, the type of stain, how long the stain has been in place and whether the surface was sealed or unsealed. Active Plus will not remove etch marks or restore polish to damaged areas. Tannin stains can return while the source of the run-off remains. For deep-set, stubborn stains see Poultice Plus or Poultice Powder.
For other stains and problems, see our Problem Solvers and the Stain Removal Guide.
For additional options, contact the Sealers Plus Technical Services Team at support@sealersplus.com.au or call +61 2 9521-4000 with details of the problem you are addressing.
Important note
These recommendations are general guidelines for problem solving. Actual dilution ratios and cleaning requirements may vary depending on the surface, the use, the amount and the method of application.Read the entire Product Label, SDS and Technical Bulletin before using any product.
ALWAYS TEST A SMALL AREA to determine the ease of application, dilution, dwell time and desired results.
Keep the surface clean and dry to reduce the possibility of slip-fall accidents.

